|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
APM2.6 ArduPilot Mega 2.6 APM Flight Control Board Exterbal Compass w/ Protective Case for Multicopter
Introduction:
This is the new APM 2.6 autopilot module. The sensors are exactly the same as with APM2.5+, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.
The APM 2.6 is a complete open source autopilot system and
|
|
|
|
|
The Arkbird Autopilot System w/OSD is an all-in-one solution for your FPV models navigation. This unit is loaded with features such as GPS waypoint flight, "Return to Home" functionality, auto-leveling, altitude hold and much more! It utilizes GPS, barometer and attitude sensors to stabilize/control your models flight.
Worried about losing control of your FPV model when flying out of sight? W
|
|
|
|
|
The Dianmu FPV Flight Controller with integrated OSD and GPS is the all-round solution for your FPV airplane. Supporting both traditional and delta wing models, it is designed to suit just about any fixed-wing FPV application.
Not only does the Dianmu offer gyro/accelerometer based flight stabilization, it also integrates OSD functionality with 80A current sensing, GPS, altitude holding, Return
|
|
|
|
|
FlyCam MultiCopter Controller " Black-32 " + FlyCam GPS
Features:
Modern 32-bit ARM processor running at 3.3V/72MHz.
2000 degrees/second 3-axis MEMS gyro, accelerometer(MPU6050)
3-axis magnetometer (HMC5883L) and pressure sensor(MS5611).
Support Quad-, Tri-, Hex-, Octo-, various coaxial configurations, as well
As fully customizable motor mixer for any multicopter type.
8ch RC input-On board PPM convert for Standard, CCPM, Spektrum satellite, S.BUS
Battery voltage monitoring a
|
|
|
|
|
The F-TEK 31AP is an inertial attitude measurement instrument used for automated stabilizationof fixed wing model aircraft and simple three axis camera gimbals It features anintegrated three-axis gyro and three-axis accelerometer which controls the aircraft movementin three-dimensional space.
The F-TEK 31AP also incorporates an accurate barometric pressure sensor.
At start up, the take-off air
|
|
|
|
|
The F-TEK OSD overlays flight telemetry information onto your video image.
The telemetry information displayed includes flight altitude, flight speed, flight direction, homedirection, GPS positioning and more. You also can save the telemetry information to a MICRO SD card (available separately).
The F-TEK OSD automatically adapts to either PAL or NTSC video input and confirms if there is a MICRO SD card or not.The adaptive processes are within about 20 seconds.Once the input vi
|
|
|
|
|
FY-901 je inerciální stabilizační systém pro multikoptéry. Díky současné instalaci tříosého gyroskopu a tříosého akcelerometru nabízí tato řídící deska pokročilé řešení "vše v jednom" pro velmi stabilní let jakékoliv multikoptéry!
FY-901 nabízí dva letové režimy, které mohou být přepínány pomocí RC soupravy i během letu:
Auto-stabilizační režim: V tomto režimu je využívaný tříosý akcelerometr pro autostabilizaci modelu tak, aby ramena multikoptéry byla vždy v jejich neutrální poloze. Tento režim je skvělý pro po
|
|
|
|
|
These self-adhesive foam mounting pads are the same as those sold by the big name brands but ata fraction of the price! This material is soft enough to provide excellent vibration dampening yet
rigid enough to keep your device from moving around. These properties make it the ideal choice for gyro,flybarless system and flight controller mounting. The materials used in these pads are sourceddirectly
|
|
|
|
|
The HKPilot Mega 2.5 is a complete open source autopilot system featuring the best selling technology. This version is ready to use, with no assembly required. It allows the user to turn any fixed wing, rotary wing or multi-rotor vehicle (even boats and car) into a fully autonomous vehicle capable of performing programmed GPS missions with waypoints (GPS module required - sold separately).
Feat
|
|
|
|
|
Controlled by an Atmel Mega168PA 8-Bit RISC based micro controller and utilizing a single high precision 3-axis MEMS gyro, the Hobbyking i86AP Flight Stabilization Control Board is capable of stabilizing flight on just about any fixed wing aircraft! It provides added stability by automatically correcting the aileron, elevator and rudder channels in flight. This compensates for unwanted changes in
|
|
|
|
|
KK2.0 byl navržen od základu tak, aby mohl létat s multicopterami každý.
Díky LCD obrazovce je instalace a nastavení jednodušší, než kdy jindy. Letové typy multi-copter jsou již předinstalovány. Jednoduše vyberete letový typ, zkontrolujete správné rozložení motorů, směr vrtulí, zkalibrujete a můžete letět!
Původní KK gyroskop je nahrazen neuvěřitelně citlivým dvojčipovým 3-osým gyroskopem a jednočipovým 3-osým akcelerometrem. Srdcem KK2.0 je Atmel Mega324PA 8-bit AVR RISC mikroprocesor s 32kB pamětí.
Do KK2.0 byly přidány
|
|
|
|
|
This is a mini Arduino based on-screen display board.
Its tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible.
It main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader,
and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin cable.
It features two independent power and ground sections to isolate the OSDs analog stage: a +5V section for the ATmega and th
|
|
|
|
|
This is a mini Arduino based on-screen display board.
Its tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible.
It main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader,
and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin cable.
It features two independent power and ground sections to isolate the OSDs analog stage: a +5V section for the ATmega and th
|
|
|
|