DIY Elektonika » Arduino
| položek: 29 | Seřadit: Dle názvu A→Z| Od nejlevnějšího| Dle kódu 0→9| Od nejnovějšího |
|
|
Kód zb.:
YO705-jg
Cena: 369.00 ,- CZK |
|
Arduino Nano V3.0 Microcontroller BoardArduino Nano je malá, ale přesto kompletně vybavená řídící deska založena na procesoru ATmega328.Má srovnatelnou funkcionalitu jako Arduino Duemilanove, ale v odlišném balení.Postrádá pouze DC napájecí zdířku a je osazená Mini-B USB kabelem. Nano 3.0 má řadu možností, jak komunikovat s počítačem, jiným Arduino zařízením nebo jiným mikroprocesorem.ATmega328 poskytuje UART TTL (5V) seriovou komunikaci, která je dostupná na digitálním pinu 0 (RX) a 1 (TX).FTDI FT232RL umožňuje seriovou komunikaci přes USB a FTDI driver (součást Arduino software) poskytuje virtuální COM p |
||
|---|---|---|
|
Kód zb.: CR685-rk Cena: 221.00 ,- CZK |
|
Arduino Digital Output Port ShieldThis HC595 device contains an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. The storage register has parallel 3-state outputs. Separate clocks are provided for both the shift and storage register. The shift register has a direct overriding clear (SRCLR) input, serial (SER) input, and serial outputs for cascading. When the output-enable (OE) input is high, the outputs are in the high-impedance state. Both the shift register clock (SRCLK) |
||
|---|---|---|
|
Kód zb.: AF706-y5 Cena: 819.00 ,- CZK |
|
LCD 12864 Module V2.0 for ArduinoThis LCD module uses a 128x64 liquid crystal display which can support Chinese characters, English characters and even graphics. It is suitable for interactive work with Arduino. It features a backlit display, parallel or serial control, adjustable contrast and more. It can be connect to an interface shield via IDC6 socket and cables. The LCD is shipped in parallel mode in default. The R9 is used to set the interface mode. To switch to SPI mode, the R9 resistor needs to be moved |
||
|---|---|---|
|
Kód zb.: BX988-oy Cena: 1268.00 ,- CZK |
|
Arduino 10DOF (L3G4200DplusADXL345plusHMC5883LplusBMP085) Sensor Stick Breakout- for MWC/KK/ACMThis 10DOF sensor breakout is a very small sensor board with 10 degrees of freedom.It includes the ADXL345 accelerometer, HMC5883L magnetometer, BMP085 and the L3G4200D gyro.This break has a simple I2C interface and a mounting hole for fixing to your multi-project. The ADXL345 is a small, thin, ultra-low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g.Digit |
||
|---|---|---|
|
Kód zb.: YN866-nj Cena: 330.00 ,- CZK |
|
Arduino Sensor Shield V4 digital analog moduleArduino Sensor Shield V4.0 umožňuje "plug and play" propojení různých modulů, jako jsou senzory,serva, relé, tlačítka, potenciometry atd. Každý funkční modul má k dispozici ports VCC, GND, propojený s odpovídajícím IO portem na desce Arduino Sensor Shield,který umožňuje propojení 2.54mm kabelem samice-samice. Specifikace: - Plug & play. - Provozní napětí: 5V stejnosměrných - Vstupní napětí (doporučené): 7-12V stejnosměrných - Vstupní napětí (limitní): 6-20V stejnosměrné - Analogové porty: Pevně spojené s šesti analogovými vstup |
||
|---|---|---|
|
Kód zb.: PU025-17 Cena: 662.00 ,- CZK |
|
Arduino Ethernet Shield V1.1With this Ethernet Shield, your Arduino board can be connected to internet. It features an ENC28J60 SPI Ethernet controller with HR911102A RJ45 socket. It supports use of a web client application to use Arduino as a distributed network sensor. This shield is stackable by accepting prototype shields or any other boards with an Arduino compatible interface. Specification: Function: Ethernet Shield (w/RJ45 socket) for Arduino Dimensions: 70x57x17mm Weight: 27g |
||
|---|---|---|
|
Kód zb.: MG824-lc Cena: 412.00 ,- CZK |
|
Arduino V0.3 XBee PRO Shield for Wireless ModuleThe Arduino V0.3 XBee PRO shield features a stackable design which makes it more convenient to connect with other expansion boards. It solves the problem of the previous version not being able to match some other expansion boards. Features: • This Arduino XBee shield allows the Arduino to communicate wirelessly over a modified ZigBee protocol using the popular XBee module. • It is a fully As |
||
|---|---|---|
|
Kód zb.: CU542-wa Cena: 215.00 ,- CZK |
|
Arduino Lamp ModuleArduino Lamp Module |
||
|---|---|---|
|
Kód zb.: IC827-u1 Cena: 335.00 ,- CZK |
|
Arduino MQ-2 Gas Sensor, Smoke, Methane, Butane DetectionArduino MQ-2 Gas Sensor, Smoke, Methane, Butane Detection Specification: Operating Voltage: 5V |
||
|---|---|---|
|
Kód zb.: QY418-i0 Cena: 560.00 ,- CZK |
|
Arduino Triple-Axis Digital Output Gyro Sensor ITG-3205 ModuleThis is a breakout board for InvenSense ITG-3205, a groundbreaking triple-axis, digital output gyroscope.The ITG-3205 is the world’s first single-chip, digital-output, 3-axis MEMS gyro IC optimized for gaming, 3D mice, and 3D remote control applications. The part features enhanced bias and sensitivity temperature stability, reducing the need for user calibration. Low frequency noise is lower t |
||
|---|---|---|
|
Kód zb.: OL109-7d Cena: 610.00 ,- CZK |
|
Arduino Uno R3 Microcontroller - Atmel ATmega328The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC ada |
||
|---|---|---|
|
Kód zb.: QF228-ke Cena: 409.00 ,- CZK |
|
Arduino Sensor Shield V5.0 Sensor Expansion BoardThe Arduino Sensor Shield V5.0 allows plug and play connection to various modules like sensors, servos, relays, buttons, potentiometers and more. Features: I2C interface Bluetooth module communication interface SD card module communication interface APC220 wireless RF modules communication interface RB URF V1.1 ultrasonic sensors interface 12864 LCD serial and parallel interface 32 servo control |
||
|---|---|---|
|
Kód zb.: LZ989-jl Cena: 859.00 ,- CZK |
|
MultiWii NanoWii ATmega32U4 Micro Flight Controller USB/GYRO/ACCThe NanoWii is a complete multi-rotor flight controller. It is based on the ATmega32U4, whichis the processor of the Arduino Leonardo and incorporates a MPU-6050 chip, which is a combinedgyro and accelerometer. This is the ultimate solution for powerful flight performance with your multi-rotor project,especially micro size models. The possibilities are endless with the NanoWii,only limited by y |
||
|---|---|---|
|
Kód zb.: MW625-79 Cena: 131.00 ,- CZK |
|
Arduino Mini Flame Fire Wavelength SensorThis sensor detects flame and light sources with wavelength range from 760 nanometre to 1100 nanometre. Approximately 60 degree Detection Angle. This sensor has particularly high sensitivity to flame. Necessary for Fire-fighting robots. Features: Adjustable Sensitivity 5V Working Voltage. Specification: Output: DO for Digital Output, AO for Analog Output. Dimension: 44*17mm |
||
|---|---|---|
|
Kód zb.: CQ429-70 Cena: 351.00 ,- CZK |
|
Arduino USBtinyISP V2.0USBtinyISP V2.0 (Arduino-kompatibilní) je ISP downloader pro AVR mikrokontroléry založené na rozhraní USB.Lze jej použít pro většinu AVR procerorů. V Arduino IDE, USBtinyISP je downloader,který je podporován v každém okamžiku, což je jednoduché a pohodlné použití. Specifikace: Rozměry: 49 x 48 x 12 mm Hmotnost: 17.3g |
||
|---|---|---|
If you have any comments or questions about this site, please direct them to the Webmaster
Datum aktualizace 14.02.2015 ver. 2.00.571 info@modelmania.cz
Vaše IP adresa je: 18.191.84.33
