|
|
|
Plush 6A Střídavý regulátor otáček
Model Plush: 6A
Nepřetržitý proud: 6A
Burst: 8A
BEC: Lineární
BEC Výstup: 5v/.8A
Lipo Počet: 2cell
NiMH: 5-6
Programability: Programovací karty nebo radiovým ovladačem
Hmotnost: 6 g
Velikost: 24x12x6mm
|
|
|
|
|
Turnigy® dlux ESCs have set a new bench mark in quality and performance.Each ESC uses a twin PCB design separating the motor power supply & MCU.This design allows for optimum component layout on each PCB and provides the ideal configuration for heat dissipation and thermal efficiency.Both PCBs are enclosed in a full aluminum heat sink casing to ensure maximum heat dispersion.All Turnigy dlux ESCs
|
|
|
|
|
The Turnigy TrackStar 1/18th scale 18amp car ESC is the latest addition to Hobby Kings Car ESC range.
Using a Fast Silicon Labs MCU and high quality On-Semiconductor MOSFETs the TrackStar 18A ESC sets a new standard in high quality yet affordable car ESCs. With Intelligent MCU logic the TrackStar series ESCs allow extremely precise start up control and positioning feed back from the motor. This t
|
|
|
|
|
The Turnigy AE series are based on new powerful microprocessor.
The new CPU means ultra fast sync timing, crisper throttle response, less battery load and reduced FET heat buildup. Also there is a separate voltage regulator IC for microprocessor providing good anti-jamming capability.
Specification:
Output: Continuous 65A, burst 70A up to 10 seconds.
Input Voltage: 2-6 cells lithium battery or 5-18 cells NIMH battery.
BEC: Linear 4A @ 5V
Control Signal Transmission: Optically
|
|
|
|
|
MultiStar ESCs are are a quality speed controller at a fantastic price! Designed for simple installation and easy setup these ESCs have proven to offer excellent performance when used in Multi-rotor applications. If your starting out in Multi-rotors and need an easy to install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered.
These ES
|
|
|
|
|
The Turnigy TrackStar 1/10th scale 60amp car ESC is the latest addition to Hobby Kings Car ESC range.
Using a Fast Silicon Labs MCU and high quality On-Semiconductor MOSFETs the TrackStar 60A ESC sets a new standard in high quality yet affordable car ESCs. With Intelligent MCU logic the TrackStar series ESCs allow extremely precise start up control and positioning feed back from the motor. This tr
|
|
|
|
|
Ultra fast microprocessor controlled, extremely low resistance circuit and chip design, and aluminum heatsink for better thermal dissipation are just some of the features in the new TURNIGY Super Brain range of brushless speed controllers.
The Super Brain brushless esc is a high performance ESC capable of standard and competition use.
Full protection, including signal loss, over-temperature.
Programable by USB, PC or your Tx.
Compatible with all radio systems.
Features:
Supports
|
|
|
|
|
Designed and manufactured by HobbyKing, this handy UBEC features a built in safety buzzer to warn you if your input power source drops below 6V.
Specification:
Current: 3A (Max. 4A)
Input voltage: 6V ~ 23V (2S ~ 5S Lipo)
Optional Output: 5.1V or 6.1V
Weight: 13.6g (including wires)
|
|
|
|
|
Plush 30 Brushless Speed Controller
The Plush series ESC are a very good quality controller.They have a broad range of programming features and a smooth throttle response compared to other BESCs in the same price range.
All our BESCs come with a full warranty.
Specification:
Cont Current: 30A
Burst Current: 40A
BEC Mode: Linear
BEC: 5V / 2A
Lipo Cells: 2 - 4
NiMH: 5 - 12
Weight: 25g
Size: 45x24x11mm
User Programmable, both via controller and optional programming card.The progr
|
|
|
|
|
TURNIGY marine ESCs are built with USA IR mosFETs for long run times and less heat.
Boat escs have a different requirement to air or car escs.
Their need for sustained high-amp draw makes plane escs unsuitable and car escs
with large amp spike capability, unnecessary.
Thats why TURNIGY marine escs are designed purely for boats, and coated in anti-static then water resistant laquer to prevent shorting should the esc get wet.
They can handle sustained high amp/volt loads and handle
|
|
|
|
|
The Turnigy AE series are based on new powerful microprocessor.
The new CPU means ultra fast sync timing, crisper throttle response, less battery load and reduced FET heat buildup. Also there is a separate voltage regulator IC for microprocessor providing good anti-jamming capability.
Specification:
Output: Continuous 20A, burst 25A up to 10 seconds.
Input Voltage: 2-4 cells lithium battery or 5-12 cells NIMH battery.
BEC: Linear 2A @ 5V
Control Signal Transmission: Optically
|
|
|
|
|
DP 3A je malá (asi 1 g), střídavý regulátor postavený pouze na jediné buňky aplikace a pro odběr proudu až do maximální výše 4A praskne.
Tento střídavý ESC je pouze k použití pro Lipoly jedné buňce aplikace, kde je potřeba více než 3A konstantní.
Vlastnosti:
Vysoká rychlost MCU. Rychlé řešení pro elegantní rychlejší odezva na plyn a vynikající nízké rychlosti časování.
Ochranu buňky, signál ztratil zabezpečený proti poruchám.
Hladké
|
|
|
|
|
Možnosti programování
Napětí Odřízněte
přetáhněte brzdy
zpětného výkonu
Začátek výkonu
Vyhovuje Turnigy stopy hvězda 60A ESC.
|
|
|
|
|
Our largest ESC yet! the Turnigy Fatboy speed controller is rated at a massive 300 Amp continuous current draw and 380 Amp burst!
The Fatboy features a large Aluminum heat sink case, twin brushless cooling fans, dual 10AWG input wires, built in anti-spark protection and 8mm female bullet terminals for the motor output.
A programming box has also been included with the Turnigy Fatboy to make setup fast and easy. This ESC is suited to large scale 100cc plus Electric conversions.
|
|
|
|
|
Turnigy® dlux SBEC ESCs have set a new bench mark in quality and performance. Each ESC uses a twin PCB design separating the motor power supply, MCU and SBEC. This design allows for optimum component layout on each PCB and provides the ideal configuration for heat dissipation and thermal efficiency. Both PCBs are enclosed in a full aluminum heat sink casing to ensure maximum heat dispersion. All
|
|
|
|