|
|
|
Arduino Sensor Shield V4.0 umožňuje "plug and play" propojení různých modulů, jako jsou senzory,serva, relé, tlačítka, potenciometry atd. Každý funkční modul má k dispozici ports VCC, GND, propojený s odpovídajícím IO portem na desce Arduino Sensor Shield,který umožňuje propojení 2.54mm kabelem samice-samice.
Specifikace:
- Plug & play.
- Provozní napětí: 5V stejnosměrných
- Vstupní napětí (doporučené): 7-12V stejnosměrných
- Vstupní napětí (limitní): 6-20V stejnosměrné
- Analogové porty: Pevně spojené s šesti analogovými vstup
|
|
|
|
|
Designed in house by the HobbyKing Enginerds, this handy power distribution board has the same footprint as our Multri-rotor control boards and is the ultimate solution for tidy power distributionwiring. Simply use 3.5mm male connectors on your ESCs and plug a battery in.The PCB is Gold plated for optimality efficiency and also features a bling port (aka 2 pin JST sizeauxiliary power out) Perfect
|
|
|
|
|
Tarot needs no introduction, their name is synonymous with quality and there 2 axis ZYX22 gimbal controller is no exception.
The Tarot ZYX22 Brushless gimbal controller is unique from all the other run of the mill BLGC on the market, they removed the FTDI chip from board to save size and weight, but is just as easy to use with the included USB adapter. And Tarots computer user interface for se
|
|
|
|
|
Designed for use with our Multistar 15 amp esc, this cable simplifies the construction of your Hexacopter power system by allowing you to simply plug the system together - Plug and play style and with zero soldering!
This cable comes pre terminated with an XT60 battery input and terminates in 6 pairs of 3.5mm female gold connectors.Wiring is silicone insulated 14 Awg - splitting into 18 Awg.
|
|
|
|
|
Designed for use with our Multistar 15 amp esc, this cable simplifies the construction of your Tricopter power system by allowing you to simply plug the system together - Plug and play style and with zero soldering!
This cable comes pre terminated with an XT60 battery input and terminates in 3 pairs of 3.5mm female gold connectors.Wiring is silicone insulated 14 Awg - splitting into 18 Awg.
|
|
|
|
|
The MultiWii 328P is a gyro/accelerometer based flight controller that is loaded with features.
This version of the MultiWii supports DSM2 satellite receiver functionality.
With expandability options and full programmability, this device can control just about any type of aircraft.
This is the ideal flight controller for your multi-rotor aircraft.
Features:
• SMD component design with Atmega32
|
|
|
|
|
This handy bluetooth module is used to configure your Multiwii flight controller wirelessly from your Android device. You will need to download the Multiwii Configuration Android app to your mobile device to use this module.
MultiWii Configuration App functions:
Read and Write PID
Setting switch adjustment for AUX1 and AUX2
Monitor receiver signal and FC output signal
Monitor all sensors and G
|
|
|
|
|
The F-TEK 31AP is an inertial attitude measurement instrument used for automated stabilizationof fixed wing model aircraft and simple three axis camera gimbals It features anintegrated three-axis gyro and three-axis accelerometer which controls the aircraft movementin three-dimensional space.
The F-TEK 31AP also incorporates an accurate barometric pressure sensor.
At start up, the take-off air
|
|
|
|
|
This is a mini Arduino based on-screen display board.
Its tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible.
It main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader,
and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin cable.
It features two independent power and ground sections to isolate the OSDs analog stage: a +5V section for the ATmega and th
|
|
|
|
|
KK2.0 byl navržen od základu tak, aby mohl létat s multicopterami každý.
Díky LCD obrazovce je instalace a nastavení jednodušší, než kdy jindy. Letové typy multi-copter jsou již předinstalovány. Jednoduše vyberete letový typ, zkontrolujete správné rozložení motorů, směr vrtulí, zkalibrujete a můžete letět!
Původní KK gyroskop je nahrazen neuvěřitelně citlivým dvojčipovým 3-osým gyroskopem a jednočipovým 3-osým akcelerometrem. Srdcem KK2.0 je Atmel Mega324PA 8-bit AVR RISC mikroprocesor s 32kB pamětí.
Do KK2.0 byly přidány
|
|
|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
Prodlužovací servo kabely 26 AWG o délce 3 cm s konektory samec-samec (10 ks v balení)
|
|
|
|
|
Na základě popularity oblíbené KK řídící desky pro quadricoptéry, vychází i HobbyKing vstříc qudricoptérovému šílenství a nabízí svou řídící desku se skvělým poměrem ceny a kvality!
Základní deska pro quadricoptéru od HobbyKing je osazena piezo gyry od japonské firmy Murata, která jsou méně citlivá na otřesy, než standardní SMD gyra a u kterých způsob jejich výroby zajišťuje stálou kvalitu. Deska je dále osazena uživatelem programovatelným Atmega168PA procesorem.
Specifikace:
Rozměry: 50.5 mm x 50.5 mm x 23.5 mm
Hmotnost:
|
|
|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
Designed for use with our Multistar 15 amp esc, this cable simplifies the construction of your Quadcopter power system by allowing you to simply plug the system together - Plug and play style and with zero soldering!
This cable comes pre terminated with an XT60 battery input and terminates in 4 pairs of 3.5mm female gold connectors.Wiring is silicone insulated 14 Awg - splitting into 18 Awg.
|
|
|
|