|
|
|
The Turnigy TrackStar 1/18th scale 18amp car ESC is the latest addition to Hobby Kings Car ESC range.
Using a Fast Silicon Labs MCU and high quality On-Semiconductor MOSFETs the TrackStar 18A ESC sets a new standard in high quality yet affordable car ESCs. With Intelligent MCU logic the TrackStar series ESCs allow extremely precise start up control and positioning feed back from the motor. This t
|
|
|
|
|
The Turnigy series are programmable car and boat brushless speed controllers. The Turnigy series boasts features such as large burst currents, programmable breaking and reverse, low resistance, 2-3 Lipo cell capable and low weight.
Specification:
Cont. Current: 60A
Burst Current: 380A
Resistance: 0.0007ohm
Car Size: 1/10
Suggested Motor: Around 5.5T / 3650kv
Battery: 2-3 Cell Lipo / 4-9 Cell Ni-
|
|
|
|
|
Turnigy® TRUST SBEC ESCs have a very flexible and broadly capable MCU, able to run all types of brushless motors.
The large heatsink and simple PCB layout make heat dissapation consistant, enabling the ESC to be run at its limit, without failure.
The ESC is program-card and transmitter programmable with clear and easy to understand instructions included.
Default factory settings are:
Brake: off
B
|
|
|
|
|
MultiStar ESCs are are a quality speed controller at a fantastic price! Designed for simple installation and easy setup these ESCs have proven to offer excellent performance when used in Multi-rotor applications. If your starting out in Multi-rotors and need an easy to install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered.
These ES
|
|
|
|
|
Ultra fast microprocessor controlled and extremely low resistance circuit and chip design, water-proof PCB, and aluminum water-cool heatsink for better thermal dissipation are just some of the features in the new TURNIGY Aquastar range of brushless boat speed controllers.
The AquaStar brushless esc is a high performance ESC capable of standard and competition use.
Full protection, include signal l
|
|
|
|
|
Turnigy® dlux SBEC ESCs have set a new bench mark in quality and performance, so much so that this lightweight and highly versatile ESC can handle up to 6s and + 10A burst current with complete peace of mind. The extensive programming and data Logging features also offer a versatility of applications rarely seen in an ESC of this rating. All Turnigy dlux ESCs can be programmed via a programing ca
|
|
|
|
|
Ultra fast microprocessor controlled and extremely low resistance circuit and chip design, water-proof PCB, and aluminum water-cooled heatsink for better thermal dissipation are just some of the features in the new TURNIGY Aquastar range of brushless boat speed controllers.
The AquaStar brushless esc is a high performance ESC capable of standard and competition use.
Full protection, include signal loss, temperature, and motor jam protection. Programmable by your Tx.
Compatible t
|
|
|
|
|
Turnigy® TRUST SBEC ESCs have a very flexible and broadly capable MCU, able to run all types of brushless motors.
The large heatsink and simple PCB layout make heat dissapation consistant, enabling the ESC to be run at its limit, without failure.
The ESC is program-card and transmitter programmable with clear and easy to understand instructions included.
Default factory settings are:
Brake: off
B
|
|
|
|
|
TURNIGY marine ESCs are built with USA IR mosFETs for long run times and less heat.
Boat escs have a different requirement to air or car escs.
Their need for sustained high-amp draw makes plane escs unsuitable and car escs
with large amp spike capability, unnecessary.
Thats why TURNIGY marine escs are designed purely for boats, and coated in anti-static then water resistant laquer to prevent shorting should the esc get wet.
They can handle sustained high amp/volt loads and handle
|
|
|
|
|
The Turnigy AE series are based on new powerful microprocessor.
The new CPU means ultra fast sync timing, crisper throttle response, less battery load and reduced FET heat buildup. Also there is a separate voltage regulator IC for microprocessor providing good anti-jamming capability.
Specification:
Output: Continuous 100A, burst 115A up to 10 seconds.
Input Voltage: 2-6 cells lithium battery or 5-18 cells NIMH battery.
BEC: Linear 4A @ 5V
Control Signal Transmission: Optically
|
|
|
|
|
Turnigy K-Force řady jsou založeny na zcela nový výkonný mikroprocesor obvykle vyhrazeny pro vysoké rychlosti otáček auto.Nový CPU znamená ultra rychlé synchronizace času, ostřejší reakci motoru, nižší zatížení baterie a snížení FET tepla elektřinou.
HV znamená tento model zvládne až 12S-Pol.
Specifikace:
Výstup: Kontinuální 120A, 180A burst až 10 sekund.
Vstupní
|
|
|
|
|
Turnigy® dlux SBEC ESCs have set a new bench mark in quality and performance. Each ESC uses a twin PCB design separating the motor power supply, MCU and SBEC. This design allows for optimum component layout on each PCB and provides the ideal configuration for heat dissipation and thermal efficiency. Both PCBs are enclosed in a full aluminum heat sink casing to ensure maximum heat dispersion. All
|
|
|
|
|
The Turnigy TY-P1 25Amp ESC is a stand out performer. Using quality IR HEXFET® Power MOSFETs developed in the USA, this ESC is cable of handling current draw in excess of 40 amps. However this in house designed ESC was developed and produced by the HobbyKing engineering team with one goal in mind, quality and reliability. Rather than over rate the ESC and push it to the limit with a larger heat-s
|
|
|
|
|
This Small and lightweight UBEC features a High efficiency switch mode design providing better
heat dissipation when compared to linear voltage regulators. The shielded PCB design and
output EMF coil makes helps provide a stable and low noise voltage output.
This UBEC also features built-in reverse polarity protection.
Specification:
Input: 6V-23V (2-5S Lipoly, 2-6S Li-Fe or 5-15S NiXX Battery Pack)
Output: 7.2V/4.5A (Less than 50mV peak to peak voltage @ 2A)
Dimension: 46mm x 1
|
|
|
|
|
Got an old brushed motor laying around and want to put it to good use?
The Turnigy brushed ESC is an excellent speed controller with a linear throttle curve, Lipoly/NiMh ready and programmable braking.
Specification:
Cont Current: 20A
Burst Current: 25A
BEC Mode: 5v/1A
Lipo Cells: 2-3
NiMH : 4-10
Weight: 17g
Size: 45x21x8mm
FOR USE WITH BURSHED MOTORS ONLY.
WILL NOT WORK WITH BRUSHLESS MOTORS
|
|
|
|