|
|
|
ArduPilot je plně programovatelný autopilot, který ke své činnosti vyžaduje GPS modul a infračervené senzory pro snímání polohy vůči XYZ souřadnému systému a spolu s nimi vytváří funkční UAV. Autopilot poskytuje jak funkci stabilizace, tak i funkci navigace a eliminuje tak potřebu samostatného stabilizačního systému. Podporuje také "fly-by-wire" režim, který stabilizuje model během řízení RC soupravou, díky čemuž je řízení bezpečnější a snadnější. Hardware i software jsou Opensource. Základová deska je osazena všemi součást
|
|
|
|
|
The Arduino Sensor Shield V5.0 allows plug and play connection to various modules
like sensors, servos, relays, buttons, potentiometers and more.
Features:
I2C interface
Bluetooth module communication interface
SD card module communication interface
APC220 wireless RF modules communication interface
RB URF V1.1 ultrasonic sensors interface
12864 LCD serial and parallel interface
32 servo control
|
|
|
|
|
HC-SR04 Ultrazvukový senzor používá technologii sonaru prourčení vzdálenosti k objektu - stejně jako to dělají netopýřinebo delfíni.
Tento modul nabízí vynikající přesnost a dosah. Jeho přesnostnení ovlivněna slunečním zářením nebo materiálem černébarvy (pouze akusticky měkké materiály, které snižují hluk, jakojsou látky, můžou zásadně snížit schopnost rozpoznat překážku).
Ideální doplňující snímač pro zamezení kolize pro roboty nebo multirotory!
Specifikace:
Napájení: 5V DC
Spotřeba: < 2mA
Účinný úhel: < 15°
Detekční vzdálenost: 2cm – 500 c
|
|
|
|
|
The HKPilot Mega 2.5 is a complete open source autopilot system featuring the best selling technology. This version is ready to use, with no assembly required. It allows the user to turn any fixed wing, rotary wing or multi-rotor vehicle (even boats and car) into a fully autonomous vehicle capable of performing programmed GPS missions with waypoints (GPS module required - sold separately).
Feat
|
|
|
|
|
Arduino Lamp Module
|
|
|
|
|
Model Number: DHT22
Feature:
Brand New High Quality
4-pin package
ultra-low power
No additional components
excellent long-term stability
All calibration, digital output
completely interchangeable
long distance signal transmission
relative humidity and temperature measurement
Specification:
Type: AM2302
Accuracy resolution: 0.1
Humidity range: 0-100%RH
Temperature range: -40~80
Humidity meas
|
|
|
|
|
Deska LCD a klávesnice (s konektory typu samec) pro Arduino sestává z modrého LCD displeje 16x2 a šesti tlačítek - zleva doprava jsou to tlačítka SELECT, LEFT, UP, DOWN, RIGHT a RESET. Deska může být osazena přímo do řídící desky Arduino Duemilanove, bez potřeby pájení. Jako interface do LCD slouží piny 5, 6, 7, 8 a 9.
Vlastnosti:
Dobře čitelný modrý LCD displej 16x2
Nastavitelný kontrast
Modulární konstrukce a snadná rozšiřitelnost
Použité modifikované rozhraní LCD4Bit
Modifikované rozhraní LCD4Bit:
V zájmu zachování budoucí použitelnosti SPI portů, byly dig
|
|
|
|
|
This is a 9DOF ArduIMU includes three sensors - an ITG-3205 (triple-axis gyro), ADXL345 (triple-axis accelerometer), and HMC5883L (triple-axis magnetometer). This board comes programmed with the 5V/16MHz Arduino Pro mini328 bootloader, simply connect to the serial TX and RX pins with a 5V FTDI Basic Breakout.
The outputs of all sensors are processed by an on-board ATmega328 and output over a se
|
|
|
|
|
Arduino MQ-2 Gas Sensor, Smoke, Methane, Butane Detection
Specification:
Operating Voltage: 5V
|
|
|
|
|
This shield works with Arduino to build and test prototype circuits. All pin connections are designed to be compatible with Arduino.
Specification:
Dimensions: 57x32x9mm
Weight: 5.9g
|
|
|
|
|
This 10DOF sensor breakout is a very small sensor board with 10 degrees of freedom.It includes the ADXL345 accelerometer, HMC5883L magnetometer, BMP085 and the L3G4200D gyro.This break has a simple I2C interface and a mounting hole for fixing to your multi-project.
The ADXL345 is a small, thin, ultra-low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g.Digit
|
|
|
|
|
With this Ethernet Shield, your Arduino board can be connected to internet. It features an ENC28J60 SPI Ethernet controller with HR911102A RJ45 socket. It supports use of a web client application to use Arduino as a distributed network sensor. This shield is stackable by accepting prototype shields or any other boards with an Arduino compatible
interface.
Specification:
Function: Ethernet Shield (w/RJ45 socket) for Arduino
Dimensions: 70x57x17mm
Weight: 27g
|
|
|
|
|
The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC ada
|
|
|
|
|
This HC595 device contains an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. The storage register has parallel 3-state outputs. Separate clocks are provided for both the shift and storage register. The shift register has a direct overriding clear (SRCLR) input, serial (SER) input, and serial outputs for cascading. When the output-enable (OE) input is high, the outputs are in the high-impedance state. Both the shift register clock (SRCLK)
|
|
|
|
|
The NanoWii is a complete multi-rotor flight controller. It is based on the ATmega32U4, whichis the processor of the Arduino Leonardo and incorporates a MPU-6050 chip, which is a combinedgyro and accelerometer.
This is the ultimate solution for powerful flight performance with your multi-rotor project,especially micro size models. The possibilities are endless with the NanoWii,only limited by y
|
|
|
|