|
|
|
This analog temperature sensor module is thermistor based. It measures the environment temperature and sends this information to the Arduino through the analog IO port of the Sensor Shield. Great tool for gardening projects, home alert systems etc.
Specification:
Dimensions: 35x20x18.5mm
Weight: 3.2g
|
|
|
|
|
This LCD module uses a 128x64 liquid crystal display which can support Chinese characters, English characters and even graphics. It is suitable for interactive work with Arduino. It features a backlit display, parallel or serial control, adjustable contrast and more. It can be connect to an interface shield via IDC6 socket and cables.
The LCD is shipped in parallel mode in default. The R9 is used to set the interface mode. To switch to SPI mode, the R9 resistor needs to be moved
|
|
|
|
|
The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC ada
|
|
|
|
|
Arduino Nano je malá, ale přesto kompletně vybavená řídící deska založena na procesoru ATmega328.Má srovnatelnou funkcionalitu jako Arduino Duemilanove, ale v odlišném balení.Postrádá pouze DC napájecí zdířku a je osazená Mini-B USB kabelem.
Nano 3.0 má řadu možností, jak komunikovat s počítačem, jiným Arduino zařízením nebo jiným mikroprocesorem.ATmega328 poskytuje UART TTL (5V) seriovou komunikaci, která je dostupná na digitálním pinu 0 (RX) a 1 (TX).FTDI FT232RL umožňuje seriovou komunikaci přes USB a FTDI driver (součást Arduino software) poskytuje virtuální COM p
|
|
|
|
|
|
Arduino MQ-2 Gas Sensor, Smoke, Methane, Butane Detection
Specification:
Operating Voltage: 5V
|
|
|
|
|
Arduino Nano USB
|
|
|
|
|
This is a breakout board for InvenSense ITG-3205, a groundbreaking triple-axis, digital output gyroscope.The ITG-3205 is the world’s first single-chip, digital-output, 3-axis MEMS gyro IC optimized for gaming, 3D mice, and 3D remote control applications. The part features enhanced bias and sensitivity temperature stability, reducing the need for user calibration. Low frequency noise is lower t
|
|
|
|
|
The HKPilot Mega 2.5 is a complete open source autopilot system featuring the best selling technology. This version is ready to use, with no assembly required. It allows the user to turn any fixed wing, rotary wing or multi-rotor vehicle (even boats and car) into a fully autonomous vehicle capable of performing programmed GPS missions with waypoints (GPS module required - sold separately).
Feat
|
|
|
|
|
The Arduino V0.3 XBee PRO shield features a stackable design which makes it more convenient to connect with other expansion boards. It solves the problem of the previous version not being able to match some other expansion boards.
Features:
• This Arduino XBee shield allows the Arduino to communicate wirelessly over a modified ZigBee protocol using the popular XBee module.
• It is a fully As
|
|
|
|
|
Arduino Sensor Shield V4.0 umožňuje "plug and play" propojení různých modulů, jako jsou senzory,serva, relé, tlačítka, potenciometry atd. Každý funkční modul má k dispozici ports VCC, GND, propojený s odpovídajícím IO portem na desce Arduino Sensor Shield,který umožňuje propojení 2.54mm kabelem samice-samice.
Specifikace:
- Plug & play.
- Provozní napětí: 5V stejnosměrných
- Vstupní napětí (doporučené): 7-12V stejnosměrných
- Vstupní napětí (limitní): 6-20V stejnosměrné
- Analogové porty: Pevně spojené s šesti analogovými vstup
|
|
|
|
|
This HC595 device contains an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. The storage register has parallel 3-state outputs. Separate clocks are provided for both the shift and storage register. The shift register has a direct overriding clear (SRCLR) input, serial (SER) input, and serial outputs for cascading. When the output-enable (OE) input is high, the outputs are in the high-impedance state. Both the shift register clock (SRCLK)
|
|
|
|
|
The NanoWii is a complete multi-rotor flight controller. It is based on the ATmega32U4, whichis the processor of the Arduino Leonardo and incorporates a MPU-6050 chip, which is a combinedgyro and accelerometer.
This is the ultimate solution for powerful flight performance with your multi-rotor project,especially micro size models. The possibilities are endless with the NanoWii,only limited by y
|
|
|
|
|
The MultiWii PRO is a gyro/accelerometer based flight controller that is loaded with features.This version of the MultiWii supports direct connection of a GPS module (package includes MTK 3329 GPS module)allowing for ultra-precise positioning functionality.With expandability options and full programmability, this device can control just about any type of aircraft.This is the ideal flight controlle
|
|
|
|
|
Model Number: DHT22
Feature:
Brand New High Quality
4-pin package
ultra-low power
No additional components
excellent long-term stability
All calibration, digital output
completely interchangeable
long distance signal transmission
relative humidity and temperature measurement
Specification:
Type: AM2302
Accuracy resolution: 0.1
Humidity range: 0-100%RH
Temperature range: -40~80
Humidity meas
|
|
|
|
|
This 10DOF sensor breakout is a very small sensor board with 10 degrees of freedom.It includes the ADXL345 accelerometer, HMC5883L magnetometer, BMP085 and the L3G4200D gyro.This break has a simple I2C interface and a mounting hole for fixing to your multi-project.
The ADXL345 is a small, thin, ultra-low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g.Digit
|
|
|
|