|
|
|
The NanoWii is a complete multi-rotor flight controller. It is based on the ATmega32U4, whichis the processor of the Arduino Leonardo and incorporates a MPU-6050 chip, which is a combinedgyro and accelerometer.
This is the ultimate solution for powerful flight performance with your multi-rotor project,especially micro size models. The possibilities are endless with the NanoWii,only limited by y
|
|
|
|
|
The Arduino Sensor Shield V5.0 allows plug and play connection to various modules
like sensors, servos, relays, buttons, potentiometers and more.
Features:
I2C interface
Bluetooth module communication interface
SD card module communication interface
APC220 wireless RF modules communication interface
RB URF V1.1 ultrasonic sensors interface
12864 LCD serial and parallel interface
32 servo control
|
|
|
|
|
Arduino MQ-2 Gas Sensor, Smoke, Methane, Butane Detection
Specification:
Operating Voltage: 5V
|
|
|
|
|
The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC ada
|
|
|
|
|
Model Number: DHT22
Feature:
Brand New High Quality
4-pin package
ultra-low power
No additional components
excellent long-term stability
All calibration, digital output
completely interchangeable
long distance signal transmission
relative humidity and temperature measurement
Specification:
Type: AM2302
Accuracy resolution: 0.1
Humidity range: 0-100%RH
Temperature range: -40~80
Humidity meas
|
|
|
|
|
HC-SR04 Ultrazvukový senzor používá technologii sonaru prourčení vzdálenosti k objektu - stejně jako to dělají netopýřinebo delfíni.
Tento modul nabízí vynikající přesnost a dosah. Jeho přesnostnení ovlivněna slunečním zářením nebo materiálem černébarvy (pouze akusticky měkké materiály, které snižují hluk, jakojsou látky, můžou zásadně snížit schopnost rozpoznat překážku).
Ideální doplňující snímač pro zamezení kolize pro roboty nebo multirotory!
Specifikace:
Napájení: 5V DC
Spotřeba: < 2mA
Účinný úhel: < 15°
Detekční vzdálenost: 2cm – 500 c
|
|
|
|
|
Arduino Lamp Module
|
|
|
|
|
Arduino Nano USB
|
|
|
|
|
USBtinyISP V2.0 (Arduino-kompatibilní) je ISP downloader pro AVR mikrokontroléry založené na rozhraní USB.Lze jej použít pro většinu AVR procerorů. V Arduino IDE, USBtinyISP je downloader,který je podporován v každém okamžiku, což je jednoduché a pohodlné použití.
Specifikace:
Rozměry: 49 x 48 x 12 mm
Hmotnost: 17.3g
|
|
|
|
|
Arduino 4-way Relay
|
|
|
|
|
ArduPilot je plně programovatelný autopilot, který ke své činnosti vyžaduje GPS modul a infračervené senzory pro snímání polohy vůči XYZ souřadnému systému a spolu s nimi vytváří funkční UAV. Autopilot poskytuje jak funkci stabilizace, tak i funkci navigace a eliminuje tak potřebu samostatného stabilizačního systému. Podporuje také "fly-by-wire" režim, který stabilizuje model během řízení RC soupravou, díky čemuž je řízení bezpečnější a snadnější. Hardware i software jsou Opensource. Základová deska je osazena všemi součást
|
|
|
|
|
This is a 9DOF ArduIMU includes three sensors - an ITG-3205 (triple-axis gyro), ADXL345 (triple-axis accelerometer), and HMC5883L (triple-axis magnetometer). This board comes programmed with the 5V/16MHz Arduino Pro mini328 bootloader, simply connect to the serial TX and RX pins with a 5V FTDI Basic Breakout.
The outputs of all sensors are processed by an on-board ATmega328 and output over a se
|
|
|
|
|
This is a breakout board for InvenSense ITG-3205, a groundbreaking triple-axis, digital output gyroscope.The ITG-3205 is the world’s first single-chip, digital-output, 3-axis MEMS gyro IC optimized for gaming, 3D mice, and 3D remote control applications. The part features enhanced bias and sensitivity temperature stability, reducing the need for user calibration. Low frequency noise is lower t
|
|
|
|
|
With this Ethernet Shield, your Arduino board can be connected to internet. It features an ENC28J60 SPI Ethernet controller with HR911102A RJ45 socket. It supports use of a web client application to use Arduino as a distributed network sensor. This shield is stackable by accepting prototype shields or any other boards with an Arduino compatible
interface.
Specification:
Function: Ethernet Shield (w/RJ45 socket) for Arduino
Dimensions: 70x57x17mm
Weight: 27g
|
|
|
|
|
This analog temperature sensor module is thermistor based. It measures the environment temperature and sends this information to the Arduino through the analog IO port of the Sensor Shield. Great tool for gardening projects, home alert systems etc.
Specification:
Dimensions: 35x20x18.5mm
Weight: 3.2g
|
|
|
|