|
|
|
The MultiWii 328P is a gyro/accelerometer based flight controller that is loaded with features.
This version of the MultiWii supports DSM2 satellite receiver functionality.
With expandability options and full programmability, this device can control just about any type of aircraft.
This is the ideal flight controller for your multi-rotor aircraft.
Features:
• SMD component design with Atmega32
|
|
|
|
|
Arduino Nano je malá, ale přesto kompletně vybavená řídící deska založena na procesoru ATmega328.Má srovnatelnou funkcionalitu jako Arduino Duemilanove, ale v odlišném balení.Postrádá pouze DC napájecí zdířku a je osazená Mini-B USB kabelem.
Nano 3.0 má řadu možností, jak komunikovat s počítačem, jiným Arduino zařízením nebo jiným mikroprocesorem.ATmega328 poskytuje UART TTL (5V) seriovou komunikaci, která je dostupná na digitálním pinu 0 (RX) a 1 (TX).FTDI FT232RL umožňuje seriovou komunikaci přes USB a FTDI driver (součást Arduino software) poskytuje virtuální COM p
|
|
|
|
|
|
Designed for use with our Multistar 15 amp esc, this cable simplifies the construction of your Tricopter power system by allowing you to simply plug the system together - Plug and play style and with zero soldering!
This cable comes pre terminated with an XT60 battery input and terminates in 3 pairs of 3.5mm female gold connectors.Wiring is silicone insulated 14 Awg - splitting into 18 Awg.
|
|
|
|
|
The Quanum is a DIY ground station all in one case, it is the perfect base for your Ground Station Project, from just pure FPV to full PC based mission planning. This DIY Ground station comes equipped with everything from a system voltage monitor to an 8inch LCD display, and a range of internal power and cable connections, housed in a beautiful aluminum case with locks.
The upper Case halve hou
|
|
|
|
|
FlyCam MCFC Sets
Specification:
FlyCam MCFC
FlyCam MCFC board
USB to Serial
Jumper cable (8 pieces)
LED/Buzzer
FlyCam GPS/Compass
FlyCam GPS/Compass board
External GPS module
100mm GPS module connecting cable x 2
Vibration Damper M3x15 (4 pieces)
PCB Support 50mm (4 pieces)
PCB Support 10mm (4 pieces)
|
|
|
|
|
Designed in house by the HobbyKing Enginerds, this handy power distribution board has the same footprint as our Multri-rotor control boards and is the ultimate solution for tidy power distributionwiring. Simply use 3.5mm male connectors on your ESCs and plug a battery in.The PCB is Gold plated for optimality efficiency and also features a bling port (aka 2 pin JST sizeauxiliary power out) Perfect
|
|
|
|
|
The Multiwii SE V2.0 is a gyro/accelerometer based flight controller that is loaded with features.With expandability options and full programmability, this device can control just about anytype of aircraft. This is the ideal flight controller for your multi-rotor aircraft.
Features:
Small size, 35x35mm mounting holes
6 input channels for standard receiver and PPM SUM receiver
Up to 8-axis motor output
2 servos output for PITCH and ROLL gimbal system
Can utilize a servo output t
|
|
|
|
|
The Multiwii Lite V1.0 is a gyro/accelerometer based flight controller that is loaded with features.With expandability options and full programmability, this device can control just about anytype of aircraft. This is the ideal flight controller for your multi-rotor aircraft.
Features:
Small size, 35x35mm mounting holes
6 input channels for standard receiver and PPM SUM receiver
Up to 8-axis motor output
2 servos output for PITCH and ROLL gimbal system
Can utilize a servos outpu
|
|
|
|
|
This genius tool makes flashing the Atmel Atmega MCU found in many ESCs or other devices using Atmega processors a walk in the park. No need to solder or create cumbersome clip on devices, simply connectthe socket flashing tool to a USBasp AVR device and place the socket over the exposed Atmel MCU!
Unique and exclusive to Hobbyking this handy device will become a favorite in your DIY arsenal.
Features:
High point precision.
Wide range of applications.
Quick and easy, no solde
|
|
|
|
|
Servokabel 26 AWG o délce 10 cm, zakončený na obou koncích konektorem JR (10 ks v balení)
Ideální pro propojení vašeho přijímače s řídící deskou quadrikoptéry HobbyKing.
|
|
|
|
|
This is a mini Arduino based on-screen display board.
Its tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible.
It main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader,
and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin cable.
It features two independent power and ground sections to isolate the OSDs analog stage: a +5V section for the ATmega and th
|
|
|
|
|
V ceně je obsaženo:
1 x plně osazená a propájená deska s 3 piezo gyroskopy, připravená k osazení
(SW Boodloader je předinstalován pro snadnou aktualizaci firmware)
4 x přijímačový kabel (samec/samec)
Doporučené volitelné doplňky: microUSB nebo USB propojovací seriový kabel pro snadnou aktualizaci firmware.
(Proč je použitý a předinstalovaný SW Bootloader? Protože s Bootloaderem a při použití nástroje KK Plus Flashtool, je změna firmware (což je soubor v hexadecimálním kódu)
mnohem bezpečnější a nemusíte nic programovat. Tento postup zabraňuje chybám a chybným nastavo
|
|
|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?
This Header pin type is perfect for repairing Servo pins on most 4 (or more) channel receivers.
These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCBs). They are supplied in 30 pin lengths which can bee
|
|
|
|