|
|
|
D2830-11 1000kv Brushless Motor
Specification:
Rpm/V: 1000kv
Shaft: 3.17mm
Voltage: 2S~4S (7.4v to 14.8v)
Weight: 52g
Watts: 210w
Max Current: 21A
ESC: 30A
Suggested Prop: 8x4 (4S) ~ 10x7 (2S)
Mounting Hole Bolt Circle: 16mm or 19mm
NOTE: This motor is 1000kv. The factory labelled them 1100kv in error.
|
|
|
|
|
Specification:
Dimension: 28mm x 37mm, 55mm(with shaft)
Weight: 80g (kv1000) (not including connectors)
Diameter of shaft: 4mm
Length of front shaft: 14mm
Lamination thickness: .2mm
Magnet type: 45SH
Max performance:
Voltage: 3S
Prop: EP10x5
Thrust: 1000g
Power: 300W
For:
800-1000g 3D
1200g+ Trainer
|
|
|
|
|
Specification:
Dimension: 26mm x 27mm , 40mm(with shaft)
Weight: 39g (kv1200) (not including connectors)
Diameter of shaft: 3mm
Length of front shaft: 12mm
Lamination thickness: .2mm
Magnet type: 45SH
Max performance:
Voltage: 2-3S
Prop: APC7x4
Thrust: 480g
Power: 130W
For 300~500g airplane.
|
|
|
|
|
Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.
The result is an efficient, high caliber motor using quality double shielded bearings, sint
|
|
|
|
|
NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.
Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from de
|
|
|
|
|
Designed to provide reliable and clean power for 3D parkflyers. This brushless outrunner will provide more power and with its high efficiency, long run times.
A quality motor, built specifically for planes designed to fly with a 250 watts brushless outrunner.
Specification:
Battery: 2~3 Cell /7.4~11.1V
RPM: 1320kv
Max current: 28A
No load current: 11V/0.9A
Internal resistance: 0.04 ohm
Weight: 80g (not including connectors)
Diameter of shaft: 4mm
Dimensions: 34.7x36.9mm
Require
|
|
|
|
|
Corona CS-239MG Slim-Wing Analog Servo 4.6kg/22g / 0.14sec
Specification:
Model: CS-239MG
Operating Voltage: 4.8V / 6.0V
Operating Current: 300mA / 400mA
Operating Speed: 0.15sec.60º/ 0.14sec.60º
Stall Torque: 4kg.cm /4.6kg.cm
Size: 30 x 10 x 34.5mm
Weight: 22g
Dead Band: ≤5uSec
Operating Travel: 40º/one side pulse traveling 400us
Potentiometer: 3 slider/Indirect Drive
Gear: Metal
Connector
|
|
|
|
|
Designed to be a direct swap out for your 10 size glow engine.
This brushless outrunner will provide more power and with its high efficiency, long run times.
A quality motor, built specifically for planes designed to fly with a 10 size glow engine.
Specification:
Battery: 2~3 Cell / 7.4~11.1V
RPM: 1100kv
Max current: 32A
No load current: 10V / 2.10A
Current capacity: 42A / 15sec
Internal resistance: 0.04 ohm
Weight: 149g (not including connectors)
Diameter of shaft: 5mm
Dimensio
|
|
|
|
|
NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.
Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from de
|
|
|
|
|
Specification:
Shaft Size: 3.17mm~14mm / 2.3mm~14mm (two shaft sizes included)
Motor Dimensions: ³28mm~29mm
Weight: 43g
Kv: 3500rpm/V
Battery: 2-3cell Lipo (7.4-11.1v)
Opperating Current: 8-16A
Peak Current: 19A
|
|
|
|
|
Motory řady NTM jsou motory s vnější rotací, které nabízejí robusní výkon. Jsou to motory, které mají pevné vinutí, kvalitní ložiska a magnety, vyvážený stator. Při jejich výrobě je navíc prováděna pečlivá kontrola kvality, sestávajících ze 14 kontrolních bodů, během celého výrobního procesu - od obrábění materiálů až po závěrečný zátěžový test.
Protože celý výrobní proces (od počítačového návrhu, přes výběr a obrábění materiálu až po závěrečné sestavení a testování) je soustředěný na jednom místě, je možné zaručit konstantní kv
|
|
|
|
|
Turnigy2836 brushless Outrunner 1200kv
Specification:
Dimension: 28mm x 37mm, 55mm(with shaft)
Weight: 74g (kv1200) (not including connectors)
Diameter of shaft: F4.0mm
Length of front shaft: F19mm
Lamination thickness: 0.2mm
Magnet type: 45SH
Max performance:
Voltage: 3-4S Lipoly
Prop: APC9x6
Thrust: 1100g
Power: 340W
|
|
|
|
|
NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.
Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from
|
|
|
|
|
This motor is specifically designed for the 450/500 helicopter range and a perfect fit for any of our HK450/500 helicopters.
Specification:
Model: 2223
Turns: 5
Cells: 2~3S
Kv: 3500rpm/V
No load Current: 3A/10V
Max power: 600W
Weight: 82g
Shaft diameter: 3.17mm
Dimensions: 27.2 x 42mm
Recomended ESC: 2~4S/50A
|
|
|
|
|
Specification:
Dimension: 28mm x 40mm, 56mm(with shaft)
Weight: 79g (kv2350) (not including connectors)
Diameter of shaft: ÂF4.0mm
Length of front shaft: ÂF15mm
Lamination thickness: .2mm
Magnet type: 45SH
Max performance;
Voltage: 3-4S Lipoly
Prop: APC4.7x4.25
Thrust: 800g
Power: 480W
|
|
|
|