|
|
|
4X 2212 920KV CW CCW Brushless Motor + 4 X 30A Simonk ESC for DJI Phantom F330 F450 F550 X525 Multicopter
Specification 2212 920kv Motor:
Type: 22 x 12mm
KV: 920rpm / V
Voltage: DC 7 - 12V
Weight: 53g
ESC Specification:
30A SimonK firmware Brushless ESC.
Soldered with 3pcs 3.5mm gold female plug, very convenient to connect motor.
Cont. current: 30A
Max. current: 35A
Input Voltage: 2
|
|
|
|
|
Arduino Sensor Shield V4.0 umožňuje "plug and play" propojení různých modulů, jako jsou senzory,serva, relé, tlačítka, potenciometry atd. Každý funkční modul má k dispozici ports VCC, GND, propojený s odpovídajícím IO portem na desce Arduino Sensor Shield,který umožňuje propojení 2.54mm kabelem samice-samice.
Specifikace:
- Plug & play.
- Provozní napětí: 5V stejnosměrných
- Vstupní napětí (doporučené): 7-12V stejnosměrných
- Vstupní napětí (limitní): 6-20V stejnosměrné
- Analogové porty: Pevně spojené s šesti analogovými vstup
|
|
|
|
|
KK řídící deska pro multikoptéry Blackboard (k použití v X-koptérách)
Specifikace:
Kompletně osazená SMD PCB s MEMS gyroskopy.
Právě vám představujeme novou verzi Blackboard.
FlyCam Blackboard je aktualizovaný od tvůrců kkMultiCopter.
Tato deska je stejná jako Blueboard.
Deska může být připojena k FlyCam Naviboard.
Gyroskopy:MEMS (dvousé + jednoosé)
Výstupy pro motory nebo serva: 12 kanálů
Procesor: Atmega168
Vzdálenost montážních otvorů: 45mm, 63.6mm
Tato řídící deska má shodné rozměry s deskou Blueboard.
|
|
|
|
|
ArduPilot je plně programovatelný autopilot, který ke své činnosti vyžaduje GPS modul a infračervené senzory pro snímání polohy vůči XYZ souřadnému systému a spolu s nimi vytváří funkční UAV. Autopilot poskytuje jak funkci stabilizace, tak i funkci navigace a eliminuje tak potřebu samostatného stabilizačního systému. Podporuje také "fly-by-wire" režim, který stabilizuje model během řízení RC soupravou, díky čemuž je řízení bezpečnější a snadnější. Hardware i software jsou Opensource. Základová deska je osazena všemi součást
|
|
|
|
|
Pixhawk PX4 2.4.5 32 bit ARM Flight Controller & NEO-6M GPS/4G TF Card/Led External/PPM/PM Module/433 DTM for RC Multicopter
Description:
PIXHAWK intergrated the newest 32 bit chip technology and sensor technology, get rid of the dilemma of having only 8 bit CPU of APM, and CPU occupancy being too high
Features:
with external LED -Dual Size full angle LED
Advanced 32 bit ARM CortexM4 high pe
|
|
|
|
|
This board converts a USB connection into 5 volt TX and RX that you can connect straight to the Arduino Mini or other microcontrollers, allowing them to talk to the computer.It is based on the FT232RL chip from FTDI.
Description: This is the newest revision of our FTDI Basic.We use a SMD 6-pin header on the bottom, which makes it smaller and more compact.Functionality has remained the same.
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of t
|
|
|
|
|
The Quanum is a DIY ground station all in one case, it is the perfect base for your Ground Station Project, from just pure FPV to full PC based mission planning. This DIY Ground station comes equipped with everything from a system voltage monitor to an 8inch LCD display, and a range of internal power and cable connections, housed in a beautiful aluminum case with locks.
The upper Case halve hou
|
|
|
|
|
FlyCam MultiCopter Controller " Black-32 " + FlyCam GPS
Features:
Modern 32-bit ARM processor running at 3.3V/72MHz.
2000 degrees/second 3-axis MEMS gyro, accelerometer(MPU6050)
3-axis magnetometer (HMC5883L) and pressure sensor(MS5611).
Support Quad-, Tri-, Hex-, Octo-, various coaxial configurations, as well
As fully customizable motor mixer for any multicopter type.
8ch RC input-On board PPM convert for Standard, CCPM, Spektrum satellite, S.BUS
Battery voltage monitoring a
|
|
|
|
|
Snadno použitelný alarm pro signalizaci nízkého napětí LiPo baterií, který je malý a lehký a je proto možné ho použít přímo v modelu letadla. Alarm se zapojuje do balančního konektoru LiPo baterie a detekuje nízké napětí pro každý článek. Pokud napětí na některém z článků klesne pod 3.3V, ozve se varovný zvukový signál a stavová dioda změní barvu ze zelené na červenou.
Specifikace:
Počet článků LiPo: 2S - 3S
Rozměry: 38 x 20 x 10mm
Hmotnost: 5g
Přesnost měření: 0.03V
Prahové napětí pro spuštění alarmu: 3.3V (pro každý článek)
|
|
|
|
|
This is a mini Arduino based on-screen display board.
Its tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible.
It main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader,
and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin cable.
It features two independent power and ground sections to isolate the OSDs analog stage: a +5V section for the ATmega and th
|
|
|
|
|
FlyCam MCFC Sets
Specification:
FlyCam MCFC
FlyCam MCFC board
USB to Serial
Jumper cable (8 pieces)
LED/Buzzer
FlyCam GPS/Compass
FlyCam GPS/Compass board
External GPS module
100mm GPS module connecting cable x 2
Vibration Damper M3x15 (4 pieces)
PCB Support 50mm (4 pieces)
PCB Support 10mm (4 pieces)
|
|
|
|
|
Designed for use with our Multistar 15 amp esc, this cable simplifies the construction of your Quadcopter power system by allowing you to simply plug the system together - Plug and play style and with zero soldering!
This cable comes pre terminated with an XT60 battery input and terminates in 4 pairs of 3.5mm female gold connectors.Wiring is silicone insulated 14 Awg - splitting into 18 Awg.
|
|
|
|
|
The Arduino Sensor Shield V5.0 allows plug and play connection to various modules
like sensors, servos, relays, buttons, potentiometers and more.
Features:
I2C interface
Bluetooth module communication interface
SD card module communication interface
APC220 wireless RF modules communication interface
RB URF V1.1 ultrasonic sensors interface
12864 LCD serial and parallel interface
32 servo control
|
|
|
|
|
The Multiwii SE V2.0 is a gyro/accelerometer based flight controller that is loaded with features.With expandability options and full programmability, this device can control just about anytype of aircraft. This is the ideal flight controller for your multi-rotor aircraft.
Features:
Small size, 35x35mm mounting holes
6 input channels for standard receiver and PPM SUM receiver
Up to 8-axis motor output
2 servos output for PITCH and ROLL gimbal system
Can utilize a servo output t
|
|
|
|
|
The F-TEK OSD overlays flight telemetry information onto your video image.
The telemetry information displayed includes flight altitude, flight speed, flight direction, homedirection, GPS positioning and more. You also can save the telemetry information to a MICRO SD card (available separately).
The F-TEK OSD automatically adapts to either PAL or NTSC video input and confirms if there is a MICRO SD card or not.The adaptive processes are within about 20 seconds.Once the input vi
|
|
|
|